St croix pellet stove user manual

Clean the Ash Traps. The York Insert has 2 when the stove is cold. Tip: Dip the damp towel exhaust cleanout covers see figure 8 located below in the ashes to remove stubborn buildup on the the rear brick panel.

Page 13 3. Clean holes in the Grate Weldment and Shaker Plate at least weekly. Remove the burn grate and use a small metal object to clean out plugged holes See figure 5. Figure 9 York Operations Manual Page Call your dealer for this will cover needed Periodic and Yearly service. Contact your St. Croix dealer for assistance in maintaining your stove in The Exhaust fan should be removed and top condition. Page Safe Operation Fall Startup. Prior to lighting the first fire check the outside area around the exhaust and air intake systems for obstructions.

Try all controls to see that they are working prior to lighting a York Operations Manual Page Page Troubleshooting And Faq If there is fuel in the hopper, check to see if there is an obstruction in the auger system or if the auger set screw is loose.

Solution: Remove obstruction and re-light the stove or tighten the setscrew on the auger shaft. York Operations Manual Page Page 17 Check the fuse on the back of the control board.

Replace with a Volt, 5 Amp fuse. Part Number 80PR Why is my glass dirty? Normal operation of your St. However, extended burning on the low setting only, will produce a darker tan color. Page 18 1 and 4 light at the same time. This will decrease the feed rate by.

This is the 1-Low setting, 1. The 1 Low setting will give less heat, but will also cause more build-up to form on the glass. Page 19 9. Why is my glass dirty and how to use the Fan button to help correct it? Croix stove will produce a build-up on the glass that should be wiped off on a daily basis. Page 20 Operations Manual and perform all the maintenance issues covered in the Daily and Periodic Maintenance section of the Manual.

If the stove still does not operate correctly call your Dealer for Assistance. Page 22 York Operations Manual Page Call your dealer for proper diagnosis of electrical problems and service to those components.

Pellets with high ash content or that have increased amounts of impurities or high moisture content. Every St. Croix Pellet stove model will have the same system as shown in figure 5 below. There is a 2-piece burnpot. Skip to main content. Machine VT Recommended for you St. Croix Pellet Stove Parts. Direct Brand offers all of St. Croix pellet stove parts at the lowest prices online.

Get all the top St. Croix model replacement parts at huge discounts. Direct Brand has over 19 years of experience in selling replacement parts. We will … Well, the guys came over yesterday to install the new St. Croix Prescott EXL pellet stove. As you might recall, our previous pellet stove was a Harman P I was a little nervous about switching brands because I had gotten used to Harman. Croix pellet stove parts for their top models, including the St. Our St.

Croix replacement parts are designed specifically for St. Croix stove. Have a St Croix Pellet stove Prescott On any setting the flame blows toward the shoot of the pellets. I was told to clean the stove, I did the necessary cleanings. Croix Genuine Stoves, Waco, Nebraska. Croix genuine stoves are about getting the quality you deserve from a stove that works as hard as you do.

Dust screen, ignitor, distribution blower Convection, Room , exhaust blower, and more. We have more parts than listed on the website. Croix wood pellet stove. Have your new St. The flame builds back up nicely and then the same thing happens. I feel like it would be more efficient if I could slow the feed rate down. Not sure how to do that. I have a St. Croix that is an older Prescott model.

The back plate says EX on it, but the EX is scratched into the plate. It is not stamped in. The online manual shows a different control panel than what I have on my stove. It is the manual for their newest stove.

I contacted St. Croix and they emailed me a manual for a stove that seems to be much older than mine. I guess I am somewhere in the middle. Here is a picture of my control panel: Here are the instructions on how to adjust the feeder rate from the manual that is for a newer model.

This method does nothing on my stove. Watch the LED lights to see the setting is on it will flash the new setting. This new setting will stay in memory from this point on. This gives two. This is a picture of their late model control panels: They look pretty similar. So my questions are: 1. Should my fire die down that much when pellets drop in?

How do I adjust my feed rate? I am only using the "Manual" setting. I assume I can still adjust the feed rate on the manual setting. Thanks for any input! Feb 25, 3, Northern CT.